Skip to main content

RFID glossary: tags, readers, UHF, NFC, EPC and more

This glossary defines the core terms of RFID in plain language: tags, readers, antennas, UHF, HF and NFC, EPC, middleware and more. Each entry has its own link so you can cite it, and entries based on a standard name the standard. Terms are grouped by how an RFID system is built.

What are RFID tags and chips?

RFID tag
A small device that stores an ID and replies to an RFID reader. It is attached to an item, such as a product, an asset or a card, so the item can be identified without a direct line of sight.
Also called: transponder, RFID label
Read more: How RFID works
Inlay
The thin layer inside a tag that holds the chip and the antenna together. Labels, cards and hard tags are made by wrapping an inlay in paper, plastic or another housing.
Passive tag
A tag with no battery of its own. It takes all of its operating energy from the reader's radio signal, so it needs no charging.
Source: GS1 EPC Gen2 UHF RFID Standard, Release 3.0.1, 2026
Active tag
A tag with its own power source, usually a battery, that can transmit by itself. It is typically used to track vehicles and containers rather than to label every item.
On-metal tag
A tag designed to work when fixed to metal, which can detune or block an ordinary tag. It uses a spacer or a special antenna design, so tags for tools, equipment and metal racks are chosen for the surface they sit on.
Read more: Assets & Access
EPC memory
The part of a Gen2 tag's memory that stores its Electronic Product Code, the ID the reader reports. The GS1 Tag Data Standard specifies how the contents of this memory bank are encoded.
Source: GS1 EPC Tag Data Standard, Release 2.3, 2025

What do readers and antennas do?

RFID reader
A device that sends a radio signal, listens for tag replies and passes the IDs it hears to software. It is the part that wakes a passive tag and collects its answer.
Also called: interrogator
Source: GS1 EPC Gen2 UHF RFID Standard, Release 3.0.1, 2026
Read more: How RFID works
Antenna
The part that sends the reader's radio signal out and picks the tags' replies up. Where antennas are placed and which way they point decide which tags a reader can hear.
Read zone
The area around an antenna where a reader can hear tags. It depends on the tag, the reader, the antenna and the surroundings, so it is tested on site rather than assumed.
Also called: read field
Portal
A fixed frame or gate with antennas set around a door, dock or lane. It reads every tagged item that passes through, without anyone scanning.
Read more: Warehouse & Logistics
Handheld reader
A portable reader that a person carries to the items. It is used for stock counts and for searching for one specific item.
Read more: Retail & Apparel
Read range
The distance at which a reader can still hear a tag. It changes with the frequency, the tag, the reader, the antenna and the item, so a quoted figure is only a guide until it is tested on your items.
Read more: How RFID works

Which frequencies and standards matter?

Ultra high frequency (UHF)
The radio band, 860 MHz to 930 MHz in the GS1 Gen2 standard, used by RFID systems that read many tags at a distance. It suits stock counts and doors.
Source: GS1 EPC Gen2 UHF RFID Standard, Release 3.0.1, 2026
Read more: How RFID works
High frequency (HF)
The RFID band at 13.56 MHz, used to read cards and tags held close to the reader. NFC works at the same base frequency.
Source: NFC Forum, NFC Technology: Technical Overview, 2026
Near field communication (NFC)
A contactless technology that works at 13.56 MHz over a very short distance, so a phone or card is tapped against the reader. It also lets a phone act as a contactless card.
Source: NFC Forum, NFC Technology: Technical Overview, 2026
Read more: How RFID works
Low frequency (LF)
The lowest of the RFID radio bands. It reads over a very short distance and is mostly found in older access cards and animal identification, not in item-level stock counting.
Electronic Product Code (EPC)
A standard format for the ID stored in a tag's memory, so any system can read what the number means. The GS1 Tag Data Standard defines the Electronic Product Code and the memory contents of Gen2 tags.
Source: GS1 EPC Tag Data Standard, Release 2.3, 2025
EPC Gen2
The GS1 standard for how UHF readers and tags communicate over the air, in the 860 MHz to 930 MHz range. Its full title is the EPC Radio-Frequency Identity Generation-2 UHF RFID Standard.
Also called: Gen 2
Source: GS1 EPC Gen2 UHF RFID Standard, Release 3.0.1, 2026
GS1
A global standards organization that publishes the EPC Gen2 UHF, EPC Tag Data Standard and EPCIS specifications used in item-level RFID.
Source: GS1 EPC Tag Data Standard, Release 2.3, 2025

How does RFID data reach your business systems?

RFID middleware
Software that sits between the readers and your business system. It filters duplicate and stray reads and forwards clean events, such as which item moved.
Read more: RFID + ERP/POS
EPC Information Services (EPCIS)
A GS1 standard that lets different applications create and share visibility event data, within and across companies. Not every ERP reads it directly, so middleware is usually the translation step.
Source: GS1 EPCIS Standard, Release 2.0, 2022
Read more: RFID + ERP/POS
Enterprise resource planning (ERP)
The business system that holds a company's stock, purchasing, sales and accounting records. RFID supplies counts to it, so quantities stay accurate without manual re-entry.
Read more: RFID + ERP/POS
Point of sale (POS)
The till or counter system that records each sale and updates the item record. Connected to the ERP, it keeps stock figures in step with what was sold.
Read more: RFID + ERP/POS
Stocktake
A count of the items actually on hand, checked against the system's records. With RFID a reader can hear many tagged items in one pass instead of scanning them one by one.
Also called: inventory count, stock count
Read more: Gold & Jewelry
ZATCA e-invoicing (ZATCA)
The e-invoicing (Fatoorah) program of the Zakat, Tax and Customs Authority in Saudi Arabia, which moves invoices into a structured electronic format. Cyphra's ERP and POS handle ZATCA e-invoicing, while RFID updates stock and is not itself a ZATCA system.
Source: ZATCA, E-Invoicing (Fatoorah) page, 2026
Read more: RFID + ERP/POS

Talk to us about RFID for your business

Tell us your industry and the items you need to track. We reply with the tags and readers that fit.

WhatsAppEmail